MS Primadet® millisecond series detonators are used as downlines in opencast mining and quarry operations where ‘point initiation’ is desired down the hole. The unit consists of a precise detonator assembled on a sealed length of shock tube with a J-hook at the other end.
Discover
The LP Primadet® System is a precise and reliable non-electric blast initiation system, when used in conjunction with Detacord® detonating cord, designed for use in underground bord & pillar, shaft-sinking, drop-raising and tunnelling applications. To ensure flexibility, the LP Primadet® System consists of 20 different delays that may be used in various combinations depending on the application.
Discover
The hand held SafeStart™ Initiators (SI-1) is designed to fire a SafeStart™ instantaneous detonator from a distance of up to 1km away using standard blasting wire or cable. It is primarily used for secondary blasting, but can be used to initiate a surface blast when connected with shocktube initiators.
Discover
Geoprime® is made from the highest quality PETN and other high explosive materials ensuring reliability, consistencyand durability. The product is used for seismic acquisition work. Geoprime® provides consistent energy release in all extreme seismic environments regardless of hydrostatic pressure or borehole depths.
Discover
The Dual Stoper™ non-electric blast initiation system is a precise, reliable and millisecond accurate system for sequential blasting in underground stoping, bord & pillar and in-stope tunnelling applications. The combination comprises of a Dual Det™ and either an EZ Stoper® or EZ Platinum Trunkline™ unit. They provide a fast, simple and cost effective hook-up while allowing an unlimited number of holes to be shot with inherent sequential timing.
Discover
The Combination Stoper non-electric blast initiation system is precise and reliable for sequential blasting in underground stoping and bord & pillar applications. They provide a fast, simple and cost effective hook-up while allowing an unlimited number of holes to be shot with inherent sequential timing. The combination comprises of the EZ Stoper® and LP Primadet® which have a precise non-electric, in-hole (8D) detonator that will initiate all cap sensitive explosives and ANFO. Standard delay times are available which may vary according to requirements and combinations, however the Combination Stoper only uses a 3800 / 200ms EZ Stoper® and a 3800ms LP Primadet® (number 13).
Discover
Primacord® detonating cord, when detonated, has the initiating energy of a blasting cap at all points along its entire length. The Primacord® detonating cord detonates at a speed of approximately 7000m/s. Primacord® trunklines will initiate any number of additional lengths, extensions or branch lines through correctly tied connections or knots. When used as a down line, the explosive supplier should be consulted as to the sensitivity and compatibility of cord and explosives used. Primacord® detonating cord is simple in design and use. The high explosive core is encased in various protective coverings developed to withstand the many conditions encountered in the fi eld. The difference between the standard types of Primacord® detonating cord is essentially the core load coupled with a difference in the degree of protection afforded by the encasements. Five different core load products are available, Detacord® (3.5g/m), E-cord® (5.0g/m), SB cord™ (8.0g/m), Zapcord™ (10g/m) and Zapcord™ 40 (40g/m. Various combinations of materials such as textiles and plastics cover the raw PETN (Pentaerythritol Tetranitrate) core. The textiles used provide tensile strength andflexibility, as well as resistance to abrasion and cutting, extremes of heat and cold and water and oil penetration.
Discover
Detonating cord with a high resistance to traction and impermeable to water, oil, and other liquids normally found in detonations. Allows for several explosive charges to be fired in a single detonation. Also applied in detonation circuits along with Britacron or Brinel Connect.
Discover
High grammage detonating cord with a high resistance to traction and impermeable to water and other liquids normally found in detonations. Allows for several explosive charges to be fired in a single detonation. Produced in different grammages. Recommended for use in precut and postcut blasting and sculptural blasting in open-pit and underground mining, quarries and civil construction.
Discover
The Electric Super™ Seismic detonator is ideally suited for geophysical exploration work as it fires with no appreciable time lag between the application of the proper current / amperes and detonation.The Electric Super™ Seismic detonator has the high output strength, impact resistance and superior accuracy. Now made with a copper shell, the Electric Super™ Seismic detonator offers improved corrosion resistance in the
most severe of seismic environments.
Trojan™ cast boosters deliver the driving force required for generating maximum initiating energy and blasting efficiency.They provide reliability, safety and durability for all underground mining, opencast mining and quarry applications. By combining high detonation velocity (7500m/s) with high density (1.6g/cm ), Trojan™ cast boosters optimise detonation pressure (225kbar) and consistently out perform any other type of commercial boosters. Trojan™ cast boosters are designed to be initiated by all Primadet® detonators and equivalent detonators manufactured by other suppliers. The 150g, c-400 and c-800 Trojan™ Boosters can be used with a single pass of Primacord® detonating cord with a minimum core load of 8g/m (i.e. Zapcord™ or SB cord). For specialised blasting where a lower core load is to be used (i.e. E-cord – 5g/m). It is necessaryto double loop the cord through the cord tunnel.
Discover
Thermotube is a differentiated technology that does not use explosives. Nor does it require protection for transport. As opposed to conventional tubes, which send out shock waves, with Thermotube, a high-temperature molten spark is emitted.
Discover
SafeStart™ Instantaneous Electronic Detonators provide safe, precise, reliable, blast initiation in underground mining applications. They facilitate a safe, fast and simple hook-up, for initiation of a charged panel via the main shock tube trunkline.
Discover
The SafeBlast™ Centralised Blasting System (CBS) in conjunction with the SafeStart™ Instantaneous Electronic Detonator offers improved levels of safety and reliability for blasting operations in underground mines. Once all workers have been evacuated, blasting is carried out from a centralised computer, under strict control and supervision. The system allows for all blasts within a mine to be synchronized from a dedicated computer on surface, usually the mine’s control room. The system consists of a host computer networking with a plurality of Network Slave Stations that facilitate the ultimate arming, priming and firing of SafeStart™ Instantaneous Electronic Detonators. On-board diagnostics, allows for easy fault finding while real time information allows for system and production monitoring.
Discover
The Primadet® Noiseless Trunkline Delay (NTD) non-electric delay detonator products are used as surface delays with detonating cord, and/or shock tube downlines. The system is commonly used in ‘air blast’ sensitive areas as it is considered ‘noiseless’.
Discover
The Primadet® non-electric delay detonator Noiseless Lead-in-Line (NLIL) is used as the primary initiator for mining, quarrying and construction blasts. The Noiseless Lead-in-Line, lengthens the Primadet® non-electric delay detonator surface unit being used as a primary initiator and therefore allowing the blaster to initiate the shot from a predetermined position of safety. The system is commonly used in ‘air blast’ sensitive areas as it is considered ‘noiseless’.
Discover
The EZ Trunkline™ non-electric blast initiation unit is precise, reliable and millisecond accurate, used for blasting of open pit operations, quarries and any construction application. The EZ Trunkline™ can be used in conjunction with Primadet non-electric delay products such as the EZ Det® . The EZ Trunkline™ is used with shock tube downlines only and therefore commonly used as a bridging device when problems are present or as a hook-up unit, especially in “air blast” sensitive areas, as it is considered “noiseless”.
Discover
The EZ Stoper® non-electric blast initiation system is precise and reliable for sequential blasting in underground stoping, bord & pillar and tunnelling applications. They provide a fast, simple and cost effective hook-up while allowing an unlimited number of holes to be shot with inherent sequential timing.The surface connector and cap will reliably initiate up to 3 shock tubes if properly connected, in both directions.
Discover
The EZ Ringer® non-electric blast initiation system provides precise, reliable and millisecond accurate sequential blasting in underground ring blasting applications. They provide a fast, simple and a cost effective hook-up while allowing an unlimited number of holes to be shot with inherent sequential timing. The surface connector and cap will reliably initiate up to 6 shock tubes if properly connected, in both directions.
Discover
The EZ Platinum Trunkline™ is a non-electric blast initiation unit which is precise and reliable when used in blasting of underground stoping, bord & pillar and tunnelling applications. The EZ Platinum Trunkline™ can be used in conjunction with products such as the EZ Drifter® , EZ Stoper® and Dual Stoper™ . The unit is commonly used as a starter unit, or a bridging device when problems are present and as a hook-up unit when using Dual Detonators.
Discover
The EZ Drifter® non-electric blast initiation system provides precise, reliable and millisecond accurate sequential blasting in underground stoping, bord & pillar and tunnelling applications. They provide a fast, simple and a cost effective hook-up while allowing an unlimited number of holes to be shot with inherent sequential timing.The surface connector and cap will reliably initiate up to 6 shock tubes if properly connected, in both directions.
Discover
The EZ Det® non-electric blast initiation system is precise, reliable and millisecond accurate, used in open pit mining, quarries and construction. They provide a fast, simple and a cost effective hook-up, allowing an unlimited number of holes to be fired with inherent accuracy for sequential timing. The system is commonly used in ‘air blast’ sensitive areas as it is considered ‘noiseless’.
Discover
The EZ Stoper® non-electric blast initiation system is precise and reliable for sequential blasting in underground stoping, bord & pillar and tunnelling applications. They provide a fast, simple and cost effective hook-up while allowing an unlimited number of holes to be shot with inherent sequential timing.The surface connector and cap will reliably initiate up to 3 shock tubes if properly connected, in both directions.
Discover
The EZ Ringer® non-electric blast initiation system provides precise, reliable and millisecond accurate sequential blasting in underground ring blasting applications. They provide a fast, simple and a cost effective hook-up while allowing an unlimited number of holes to be shot with inherent sequential timing. The surface connector and cap will reliably initiate up to 6 shock tubes if properly connected, in both directions.
Discover
The EZ Platinum Trunkline™ is a non-electric blast initiation unit which is precise and reliable when used in blasting of underground stoping, bord & pillar and tunnelling applications. The EZ Platinum Trunkline™ can be used in conjunction with products such as the EZ Drifter® , EZ Stoper® and Dual Stoper™ . The unit is commonly used as a starter unit, or a bridging device when problems are present and as a hook-up unit when using Dual Detonators.
Discover
The EZ Drifter® non-electric blast initiation system provides precise, reliable and millisecond accurate sequential blasting in underground stoping, bord & pillar and tunnelling applications. They provide a fast, simple and a cost effective hook-up while allowing an unlimited number of holes to be shot with inherent sequential timing.The surface connector and cap will reliably initiate up to 6 shock tubes if properly connected, in both directions.
Discover
The EZ Det® non-electric blast initiation system is precise, reliable and millisecond accurate, used in open pit mining, quarries and construction. They provide a fast, simple and a cost effective hook-up, allowing an unlimited number of holes to be fired with inherent accuracy for sequential timing. The system is commonly used in ‘air blast’ sensitive areas as it is considered ‘noiseless’.
Discover
The Dual Stoper™ non-electric blast initiation system is a precise, reliable and millisecond accurate system for sequential blasting in underground stoping, bord & pillar and in-stope tunnelling applications. The combination comprises of a Dual Det™ and either an EZ Stoper® or EZ Platinum Trunkline™ unit. They provide a fast, simple and cost effective hook-up while allowing an unlimited number of holes to be shot with inherent sequential timing.
Discover
The Combination Stoper non-electric blast initiation system is precise and reliable for sequential blasting in underground stoping and bord & pillar applications. They provide a fast, simple and cost effective hook-up while allowing an unlimited number of holes to be shot with inherent sequential timing. The combination comprises of the EZ Stoper® and LP Primadet® which have a precise non-electric, in-hole (8D) detonator that will initiate all cap sensitive explosives and ANFO. Standard delay times are available which may vary according to requirements and combinations, however the Combination Stoper only uses a 3800 / 200ms EZ Stoper® and a 3800ms LP Primadet® (number 13).
Discover
Primacord® detonating cord, when detonated, has the initiating energy of a blasting cap at all points along its entire length. The Primacord® detonating cord detonates at a speed of approximately 7000m/s. Primacord® trunklines will initiate any number of additional lengths, extensions or branch lines through correctly tied connections or knots. When used as a down line, the explosive supplier should be consulted as to the sensitivity and compatibility of cord and explosives used. Primacord® detonating cord is simple in design and use. The high explosive core is encased in various protective coverings developed to withstand the many conditions encountered in the fi eld. The difference between the standard types of Primacord® detonating cord is essentially the core load coupled with a difference in the degree of protection afforded by the encasements. Five different core load products are available, Detacord® (3.5g/m), E-cord® (5.0g/m), SB cord™ (8.0g/m), Zapcord™ (10g/m) and Zapcord™ 40 (40g/m. Various combinations of materials such as textiles and plastics cover the raw PETN (Pentaerythritol Tetranitrate) core. The textiles used provide tensile strength andflexibility, as well as resistance to abrasion and cutting, extremes of heat and cold and water and oil penetration.
Discover
DaveyTronic® SP digital blasting system for large open pit mining operations.
Discover
MS Primadet® millisecond series detonators are used as downlines in opencast mining and quarry operations where ‘point initiation’ is desired down the hole. The unit consists of a precise detonator assembled on a sealed length of shock tube with a J-hook at the other end.
Discover
The LP Primadet® System is a precise and reliable non-electric blast initiation system, when used in conjunction with Detacord® detonating cord, designed for use in underground bord & pillar, shaft-sinking, drop-raising and tunnelling applications. To ensure flexibility, the LP Primadet® System consists of 20 different delays that may be used in various combinations depending on the application.
Discover
Brinel is a family of delay detonators with non-electric initiation, used to initiate explosive charges. They provide excellent results thanks to the precision of their delay times and timely initiation, in open-pit or underground mining, quarries or civil construction. Manufactured with Thermotube, which has a differentiated technology that does not use explosives. As opposed to conventional tubes, which send out shock waves, with Thermotube, a high-temperature molten spark is emitted.
Discover